HowTo Geolocate kismet Data

***Note: Page Under Construction***

Kismet Prerequisites

Supported Wireless Card(s)

As a general rule of thumb, most WIFI adapters based on a Aetheros or Intel chip set should work "out of the box" when setting up Kismet on a NST system. To get an idea of the chip set used by your WIFI adapter, you can use the lspci command. The example output shown below is from running lspci on a ASUS Eeee PC and tells us that the system is using a Aetheros based chip set:

[root@cayenne trunk]# lspci
... Removed output for non-WIFI related hardware ...
02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01)
[root@cayenne trunk]# 

Kismet requires one or more WIFI adapters. The lspci command is useful at displaying what WIFI hardware is present on your system. However, the lspci output does not tell you whether the necessary drivers for the hardware are installed on the system. The iwconfig command will tell you what WIFI adapters are supported by the system. For example, the following shows that my system has one WIFI adapter (wlan0):

[root@cayenne trunk]# iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

wlan0     IEEE 802.11bgn  ESSID:"WRT610N-SHOP0"  
          Mode:Managed  Frequency:2.437 GHz  Access Point: 68:7F:74:03:3F:00   
          Bit Rate=65 Mb/s   Tx-Power=20 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality=50/70  Signal level=-60 dBm  
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

[root@cayenne trunk]# 

If your WIFI adapter is not recognized by the system, you may want to refer the Kismet site for more information and links. You might find information on how to download and install the necessary drivers for your your hardware.

GPS Device and gpsd Service

If you would like to be able to display the information collected by Kismet in Google Earth, you will need to connect a compatible GPS to your NST system and run the gpsd service. Refer to: "HowTo Setup The NST System With A GPS (gpsd)" for details on connecting a GPS to your NST system.

Locating the Kismet NST WUI Page

The following shows how you locate the Kismet server administrative page using the NST WUI:

Locating the kismet service in the NST WUI

Kismet Setup and Configuration

The NST ships with the necessary tools to setup and configure the system to run the kismet_server daemon. However, you must prepare and configure your system before you will be able to run the kismet_server daemon. The nstkismet script is used to prepare the system and you can run it simply by pressing the Setup System To Run Kismet button found on the Kismet Administration page. The default options shown in the image below should be sufficient for most systems.

Setting up the NST system to run kismet using the NST WUI

After pressing the Setup System To Run Kismet button, you will be taken to a page showing the results of running the nstkismet script. The output will indicate whether your wireless card was auto-detected or not. It will also tell you that you should review/edit the /etc/kismet/kismet_server.conf file and then start the kismet service. We will do these two steps using the NST WUI. For now, we simply need to press the Return button near the bottom of the page.

Results from setting up kismet using the NST WUI

After returning to the Kismet Administration page, we will set that the system has been setup to run the kismet service, but that the service is not currently running. Before starting the service, we will use the Edit Kismet Config button to review and possibly change the default configuration.

***Note: If you are not familiar with Kismet, you should use the Kismet README and Kismet Man Page buttons to read up on using Kismet before continuing.

Editing the kismet configuration file using the NST WUI

Editing the kismet source interface(s) using the NST WUI

Editing the kismet GPS configuration using the NST WUI

Starting The Kismet Service

Starting the kismet service using the NST WUI

Results from starting the kismet service in the NST WUI

Kismet Results

Stopping The Kismet Service

Stopping the kismet service using the NST WUI

Results from stopping the kismet service in the NST WUI

The Kismet Results Table

Results produced by the kismet service

MAC Addresses

00:02:2D:28:73:6F
00:8A:29:BF:7D:10
00:02:2D:BF:7D:10
D0:B0:3C:BF:7D:10
00:02:2D:BF:7D:10
00:66:00:00:00:00
00:02:2D:BF:7D:10
00:02:2D:BF:7D:10
00:02:2D:BF:7D:10
0B:1C:6B:3A:38:11
00:02:2D:BF:7D:10
00:02:2D:BF:7D:10
00:02:2D:BF:7D:10
00:02:2D:2A:60:6F
98:02:2D:28:73:6F
00:02:2D:BF:7D:10
32:C6:2C:BF:32:9D
00:02:2D:BF:7D:10

HTML Table

The summary area at the top of the HTML report generated from kismet data

The details for a particular network and its clients from the HTML report generated from kismet data

KMZ (Google Earth)

Results produced by the kismet service displayed using Google Earth

Displaying only the open WIFI networks in Google Earth

Detailed results for the PANERA network produced by the kismet service displayed using Google Earth