Dummy Interface: Difference between revisions

From MediaWiki
Jump to navigationJump to search
(New page: Reference info: '''[http://www.faqs.org/docs/linux_network/x-087-2-iface.interface.html Linux Network Administrators Guide]''')
 
No edit summary
Line 1: Line 1:
Reference info: '''[http://www.faqs.org/docs/linux_network/x-087-2-iface.interface.html Linux Network Administrators Guide]'''
Reference Info 1: '''[http://www.faqs.org/docs/linux_network/x-087-2-iface.interface.html Linux Network Administrators Guide]'''
 
Installing the Linux dummy-network interface
 
If your Linux system does not have network communication hardware installed, or if it uses the dynamic host configuration protocol (DHCP) for network IP address configuration, you can install Adaptive Server components using these procedures.
 
StepsInstalling a dummy-network interface
 
  1. Add /sbin to your $PATH environment setting:
 
      # PATH=$PATH:/sbin
 
  2. Add an IP address and host name to your /etc/hosts table. Sybase recommends that you use an address in a free Internet address band.
 
      For example, an Internet address of 10.0.0.1 would result in:
 
      echo 10.0.0.1 $HOSTNAME >> /etc/hosts
 
      NoteSybase recommends that you do not use “localhost” as an alternative.
 
 
  3. Preload the dummy network driver on the machine.
 
      # modprobe dummy
 
      If this command is successful, you do not receive any messages from the server.
 
 
  4. Bind the dummy established network interface to the $HOSTNAME configured IP address.
 
      # ifconfig dummy0 $HOSTNAME
 
 
  5. For a DHCP environment, add a route other than “default” to the established virtual network setup.
 
      # route add $HOSTNAME dummy0
 
 
  6. Check the network binding:
 
      This command gives below listed output:
 
      # ifconfig dummy0
        dummy0    Link encap:Ethernet  HWaddr 00:00:00:00:00:00
      inet addr:10.0.0.1  Bcast:10.255.255.255  Mask:255.0.0.0
      UP BROADCAST RUNNING NOARP  MTU:1500  Metric:1
      RX packets:0 errors:0 dropped:0 overruns:0 frame:0
      TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
      collisions:0 txqueuelen:0
 
7. Check the route binding:
 
      This command shows the routing as it is set up.
 
      # route
      Kernel IP routing table:
      Destination    Gateway        Genmask        Flags Metric Ref    Use Iface
      HOSTNAME        * 255.255.255.255  UH        0      0          0 dummy0
      10.0.0.0        * 255.0.0.0        U          0      0          0 dummy0
      127.0.0.0      * 255.0.0.0        U          0      0          0    lo

Revision as of 09:25, 28 April 2009

Reference Info 1: Linux Network Administrators Guide

Installing the Linux dummy-network interface

If your Linux system does not have network communication hardware installed, or if it uses the dynamic host configuration protocol (DHCP) for network IP address configuration, you can install Adaptive Server components using these procedures.

StepsInstalling a dummy-network interface

  1. Add /sbin to your $PATH environment setting:
     # PATH=$PATH:/sbin
  2. Add an IP address and host name to your /etc/hosts table. Sybase recommends that you use an address in a free Internet address band.
     For example, an Internet address of 10.0.0.1 would result in:
     echo 10.0.0.1 $HOSTNAME >> /etc/hosts
     NoteSybase recommends that you do not use “localhost” as an alternative.


  3. Preload the dummy network driver on the machine.
     # modprobe dummy
     If this command is successful, you do not receive any messages from the server.


  4. Bind the dummy established network interface to the $HOSTNAME configured IP address.
     # ifconfig dummy0 $HOSTNAME


  5. For a DHCP environment, add a route other than “default” to the established virtual network setup.
     # route add $HOSTNAME dummy0


  6. Check the network binding:
     This command gives below listed output:
     # ifconfig dummy0 
       dummy0    Link encap:Ethernet  HWaddr 00:00:00:00:00:00
      inet addr:10.0.0.1  Bcast:10.255.255.255  Mask:255.0.0.0
      UP BROADCAST RUNNING NOARP  MTU:1500  Metric:1
      RX packets:0 errors:0 dropped:0 overruns:0 frame:0
      TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
      collisions:0 txqueuelen:0

7. Check the route binding:

     This command shows the routing as it is set up.
     # route
     Kernel IP routing table:
     Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
     HOSTNAME        * 255.255.255.255  UH         0      0           0 dummy0
     10.0.0.0        * 255.0.0.0        U          0      0           0 dummy0
     127.0.0.0       * 255.0.0.0        U          0      0           0     lo