Boot Release: Difference between revisions
From MediaWiki
Jump to navigationJump to search
No edit summary |
No edit summary |
||
| (One intermediate revision by the same user not shown) | |||
| Line 22: | Line 22: | ||
* Verify that you can access the system using ''ssh'' and ''https'' after running the '''nstpasswd''' command to set the system passwords. | * Verify that you can access the system using ''ssh'' and ''https'' after running the '''nstpasswd''' command to set the system passwords. | ||
--> | --> | ||
== RPM Verify == | |||
After booting, run the following command to review verification issues in RPM packages: | |||
[root@nst30-repo repo30]# make HOST=192.168.0.9 rpm-verify | |||
... Review results of the rpm-verify output ... | |||
[root@nst30-repo repo30]# | |||
Then for a live check, run: | |||
[root@nst30-repo repo30]# make rpm-verify-diff-live | |||
... NOTE: The include/make/rpm-verify.expect.live.txt file is likely out of data | |||
don't panic if there are any issues flagged ... | |||
[root@nst30-repo repo30]# | |||
Then for a hard disk install, run: | |||
[root@nst30-repo repo30]# make rpm-verify-diff-hd | |||
... NOTE: The include/make/rpm-verify.expect.hd.txt file is likely out of data | |||
don't panic if there are any issues flagged ... | |||
[root@nst30-repo repo30]# | |||
== Probe Check == | == Probe Check == | ||
| Line 27: | Line 55: | ||
After booting the full NST Live distribution, do to your development machine and run: ''make probe-check HOST=IP'' against the newly booted NST probe. Review the resulting log file to verify that the test results look reasonable. | After booting the full NST Live distribution, do to your development machine and run: ''make probe-check HOST=IP'' against the newly booted NST probe. Review the resulting log file to verify that the test results look reasonable. | ||
[root@ | NOTE: Make sure you install your ssh keys (run '''ssh-auth-keys --hosts IP --users root''') before running the '''make''' command. | ||
[root@nst30-repo repo30]# make probe-check HOST=192.168.0.9 | |||
... Lot's of output as various checks and tests are made .. | ... Lot's of output as various checks and tests are made .. | ||
[root@ | [root@nst30-repo repo30]# less -R probe-check.log | ||
... Review results of the probe-check output ... | ... Review results of the probe-check output ... | ||
[root@ | [root@nst30-repo repo30]# | ||
Latest revision as of 09:19, 16 July 2019
It is recommended that you burn and boot from any ISO images PRIOR to uploading them to SourceForge. If you've followed all of the steps in the release guide, they should work flawlessly.
Full NST Live Distribution
- Verify that the NST Live distribution boots cleanly.
- Verify that you can log in.
- Verify that you can access the system using ssh and https after running the nstpasswd command to set the system passwords.
- Verify that you can install the distribution to hard disk.
- Verify that you can boot off the hard disk installation.
- Reboot the hard disk system.
- Verify that you can access the system using ssh and https after running the nstpasswd command to set the system passwords.
RPM Verify
After booting, run the following command to review verification issues in RPM packages:
[root@nst30-repo repo30]# make HOST=192.168.0.9 rpm-verify ... Review results of the rpm-verify output ... [root@nst30-repo repo30]#
Then for a live check, run:
[root@nst30-repo repo30]# make rpm-verify-diff-live
... NOTE: The include/make/rpm-verify.expect.live.txt file is likely out of data
don't panic if there are any issues flagged ...
[root@nst30-repo repo30]#
Then for a hard disk install, run:
[root@nst30-repo repo30]# make rpm-verify-diff-hd
... NOTE: The include/make/rpm-verify.expect.hd.txt file is likely out of data
don't panic if there are any issues flagged ...
[root@nst30-repo repo30]#
Probe Check
After booting the full NST Live distribution, do to your development machine and run: make probe-check HOST=IP against the newly booted NST probe. Review the resulting log file to verify that the test results look reasonable.
NOTE: Make sure you install your ssh keys (run ssh-auth-keys --hosts IP --users root) before running the make command.
[root@nst30-repo repo30]# make probe-check HOST=192.168.0.9 ... Lot's of output as various checks and tests are made .. [root@nst30-repo repo30]# less -R probe-check.log ... Review results of the probe-check output ... [root@nst30-repo repo30]#
