Difference between revisions of "Trouble Shooting"
(Created page with '= Why can't I boot the Network Security Toolkit? = There are several conditions which might prevent your test system from booting the Network Security Toolkit. == Using the 64 …')
Revision as of 11:10, 30 October 2010
Why can't I boot the Network Security Toolkit?
There are several conditions which might prevent your test system from booting the Network Security Toolkit.
Using the 64 bit Version 32 bit Hardware
The Network Security Toolkit is available for both a 32 bit (i686) and 64 bit (x86_64) hardware. The 32 bit version can be used on 64 bit capable hardware. However, the 64 bit version can not be used on 32 bit hardware.
BIOS Set To Boot Hard Drive
If you are using a system which typically boots from the hard drive, it is possible that the BIOS has been configured to boot directly from the hard disk. This minimizes the boot time as the BIOS doesn't need to waste time checking for a floppy or DVD each time the system starts. However, this also means that it won't boot from the Network Security Toolkit DVD.
To get around this issue, you will need to reboot the machine and quickly press the keys necessary to enter your BIOS setup. From your BIOS setup, you should be able to set the BIOS boot order.
Some systems have a BIOS which lets you select the boot device each time the system boots. If your system has this option (again you'll need to read your boot screen quickly), you can use this feature instead of reconfiguring the BIOS.
For Apple hardware, you can typically press and hold the Option key and then turn on the system to get to the list of boot choices.
BIOS Halts On Errors
A typical BIOS will stop the boot process if vital system components are missing (think keyboard here). This can become a problem if you are converting an existing computer to a bare minimal Network Security Toolkit system by removing the video card, keyboard, mouse, etc. While removing hardware is fine as far as the Network Security Toolkit is concerned, the BIOS will complain that its missing some vital component (like the keyboard) and fail to boot the NST.
To remedy this problem, you typically need to temporarily connect a keyboard and monitor to the system, enter into the BIOS configuration and configure the BIOS specific options to prevent the BIOS from halting the boot process when it detects errors. If you're smarter than me, you'll remember to do this BEFORE you strip the components from the system you are converting into a headless NST.
Finicky DVD Drive
We have seen cases where a DVD burned in one system will boot on the system which burned the DVD, but fails to boot in another system. This is a frustrating issue and tends to happen more frequently with rewritable media.
If you run into this issue:
- Double check the MD5 check sum value on your ISO image file.
- Make sure that the media type used is readable on the target system. For example, if your system won't read DVD+R media, make sure you use DVD-R media.
- Try burning your DVD on a different system or at a slower speed.
- If you were using rewritable media, try DVD-R or DVD+R media instead.
I have a 3COM 3C905C-TX-M™ managed Ethernet card. This Ethernet card has its own BIOS and attempts to boot from the local area network before falling back to booting from the local hard disk. When this feature was enabled, the system would fail to boot from the Network Security Toolkit DVD. The BIOS configuration utility built into the Ethernet card did not appear to have a means to disable this feature. I used the hardware approach to fix this issue and replaced the card.
We currently build the Network Security Toolkit for the i686 and x86_64 platforms. If you have a old generation CPU (like a original Pentium), it is unlikely that it supports the i686 architecture. You will not be able to boot the NST on these systems.
A live boot of the NST likes lots of memory. If your system runs low or out of memory, the NST will die. You may be able to boot the live NST on systems with less than 256MB of RAM, but you'd better boot to a Console mode, and don't expect to do a lot before needing to reboot the system.