Difference between revisions of "Hard Disk Install Setup Tips"
From NST Wiki
Jump to navigationJump to search (→Host Name) |
(→NIC Setup) |
||
Line 41: | Line 41: | ||
=== NIC Setup === | === NIC Setup === | ||
− | + | Set up 3 nics. On my particular system, I used two PCI cards (eth 0 and eth1) as probes and the onboard nic (eth2) as the management port | |
+ | * cdnet | ||
+ | ** Set probe ports eth0 and eth1 to static | ||
+ | ** Set management port eth2 (the onboard nic) to static, and set ip address 10.<campus>.1.6 | ||
− | |||
− | |||
− | |||
− | + | [root@nprobe9 network-scripts]# cat ifcfg-eth0 | |
− | [root@nprobe9 network-scripts]# cat ifcfg-eth0 | + | DEVICE=eth0 |
− | DEVICE=eth0 | + | BOOTPROTO=none |
− | BOOTPROTO=none | + | ONBOOT=yes |
− | ONBOOT=yes | + | # PROBE PORT 3com NIC |
− | # PROBE PORT 3com NIC | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | + | [root@nprobe9 network-scripts]# cat ifcfg-eth1 | |
+ | DEVICE=eth1 | ||
+ | BOOTPROTO=none | ||
+ | ONBOOT=yes | ||
+ | # PROBE PORT 3com NIC #2 | ||
− | + | [root@nprobe9 network-scripts]# cat ifcfg-eth3 | |
+ | DEVICE=eth3 | ||
+ | BOOTPROTO=static | ||
+ | ONBOOT=yes | ||
+ | IPADDR=10.9.1.6 | ||
+ | GATEWAY=10.9.1.1 | ||
+ | NETMASK=255.255.255.0 | ||
+ | BROADCAST=255.255.255.255 | ||
+ | NETWORK=10.9.1.0 | ||
+ | # onboard nic management interface |
Revision as of 11:29, 3 April 2007
HD Installation Recipe
The following details a set of steps to Partition Hard disk to accept two NST installations and 3 ethernet NICs.
HD Install
- Boot From CD
- Log in
- cfdisk
- create 2G NST install #1 /dev/hda1 Make bootable
- create 2G NST install #2 /dev/hda2
- Create 1G swap /dev/hda3
- create /dev/hda4 for /var/nst
- reboot
- nsthdinstall
- nsthdinstall --device /dev/hda2 --format --label "NST v1.5.0-2" --swap-devices /dev/hda5 --swap-format-label --grub-install
- nsthdinstall --device /dev/hda1 --format --label "NST v1.5.0-1" --swap-devices /dev/hda5 --swap-format-label --grub-install
- reboot to HD.
- Login with nst@2003 password.
- Create var partition, and move var to it:
mke2fs -c /dev/hda4 mkdir /newvar mount /dev/hda4 /newvar cd /var cp -ax * /newvar cd / mv var oldvar mkdir var
- Edit /etc/fstab to add
/dev/hda4 /var ext2 defaults 1 2
- reboot
Host Name
nsthostname -n nprobe2
NIC Setup
Set up 3 nics. On my particular system, I used two PCI cards (eth 0 and eth1) as probes and the onboard nic (eth2) as the management port
- cdnet
- Set probe ports eth0 and eth1 to static
- Set management port eth2 (the onboard nic) to static, and set ip address 10.<campus>.1.6
[root@nprobe9 network-scripts]# cat ifcfg-eth0 DEVICE=eth0 BOOTPROTO=none ONBOOT=yes # PROBE PORT 3com NIC
[root@nprobe9 network-scripts]# cat ifcfg-eth1 DEVICE=eth1 BOOTPROTO=none ONBOOT=yes # PROBE PORT 3com NIC #2
[root@nprobe9 network-scripts]# cat ifcfg-eth3 DEVICE=eth3 BOOTPROTO=static ONBOOT=yes IPADDR=10.9.1.6 GATEWAY=10.9.1.1 NETMASK=255.255.255.0 BROADCAST=255.255.255.255 NETWORK=10.9.1.0 # onboard nic management interface