Difference between revisions of "Hard Disk Install Setup Tips"
From NST Wiki
Jump to navigationJump to search (→NIC Setup) |
(→HD Install) |
||
Line 5: | Line 5: | ||
=== HD Install === | === HD Install === | ||
− | + | * Boot From CD | |
− | + | * Log in | |
− | + | * cfdisk | |
− | + | ** create 2G NST install #1 /dev/hda1 Make bootable | |
− | + | ** create 2G NST install #2 /dev/hda2 | |
− | + | ** Create 1G swap /dev/hda3 | |
− | + | ** create /dev/hda4 for /var/nst | |
− | + | * reboot | |
− | + | * nsthdinstall | |
− | + | ** nsthdinstall --device /dev/hda2 --format --label "NST v1.5.0-2" --swap-devices /dev/hda5 --swap-format-label --grub-install | |
− | + | ** nsthdinstall --device /dev/hda1 --format --label "NST v1.5.0-1" --swap-devices /dev/hda5 --swap-format-label --grub-install | |
− | + | ** reboot to HD. | |
− | + | ** Login with nst@2003 password. | |
− | + | ** Create var partition, and move var to it: | |
− | + | ||
− | mke2fs -c /dev/hda4 | + | mke2fs -c /dev/hda4 |
− | mkdir /newvar | + | mkdir /newvar |
− | mount /dev/hda4 /newvar | + | mount /dev/hda4 /newvar |
− | cd /var | + | cd /var |
− | cp -ax * /newvar | + | cp -ax * /newvar |
− | cd / | + | cd / |
− | mv var oldvar | + | mv var oldvar |
− | mkdir var | + | mkdir var |
− | + | ||
− | + | * Edit /etc/fstab to add | |
− | + | /dev/hda4 /var ext2 defaults 1 2 | |
− | + | * reboot | |
=== Host Name === | === Host Name === |
Revision as of 11:24, 3 April 2007
HD Installation Recipe
The following details a set of steps to Partition Hard disk to accept two NST installations and 3 ethernet NICs.
HD Install
- Boot From CD
- Log in
- cfdisk
- create 2G NST install #1 /dev/hda1 Make bootable
- create 2G NST install #2 /dev/hda2
- Create 1G swap /dev/hda3
- create /dev/hda4 for /var/nst
- reboot
- nsthdinstall
- nsthdinstall --device /dev/hda2 --format --label "NST v1.5.0-2" --swap-devices /dev/hda5 --swap-format-label --grub-install
- nsthdinstall --device /dev/hda1 --format --label "NST v1.5.0-1" --swap-devices /dev/hda5 --swap-format-label --grub-install
- reboot to HD.
- Login with nst@2003 password.
- Create var partition, and move var to it:
mke2fs -c /dev/hda4 mkdir /newvar mount /dev/hda4 /newvar cd /var cp -ax * /newvar cd / mv var oldvar mkdir var
- Edit /etc/fstab to add
/dev/hda4 /var ext2 defaults 1 2
- reboot
Host Name
{{{nsthostname -n nprobe2}}}
NIC Setup
All nodes but gr at 10.x.1.6
* cdnet * Set probe ports eth0 and eth1 to static * Set management port eth2 (the onboard nic) to static, and set ip address 10.<campus>.1.6
[root@nprobe9 network-scripts]# cat ifcfg-eth0 DEVICE=eth0 BOOTPROTO=none ONBOOT=yes
- PROBE PORT 3com NIC
[root@nprobe9 network-scripts]# cat ifcfg-eth1 DEVICE=eth1 BOOTPROTO=none ONBOOT=yes
- PROBE PORT 3com NIC #2
[root@nprobe9 network-scripts]# cat ifcfg-eth3 DEVICE=eth3 BOOTPROTO=static ONBOOT=yes IPADDR=10.9.1.6 GATEWAY=10.9.1.1 NETMASK=255.255.255.0 BROADCAST=255.255.255.255 NETWORK=10.9.1.0
- onboard nic management interface
Set the probe nic to monitor the vlan or interlink you wish to monitor. For a campus, this would be typically vlan2 on the core switch, to monitor all traffic inbound/outbound to the campus.